-40%
XL4015 5A DC-DC Step Down Buck Converter Module Power Supply LED Lithium Charger
€ 2.16
- Description
- Size Guide
Description
XL4015 5A DC-DC Step Down Buck Converter Module Power Supply LED Lithium ChargerItem 1
The DC-DC module based on LM2596 advocate current to 3.0A, but only to 1.8A.However, being introduced module adds a heatsink, using high-power devices.This module can easily reach 4A, 50W, add heat sink circumstances can reach 75W, has a high price!!
Module highlights: 5A high power、high efficiency and low ripple with power indicator !!!
Input voltage range：4～38VDC(Note:input voltage not exceeding 38V)
Output voltage range：1.25-36VDC adjustable
Output current: 0-5A, recommended for use in 4.5A.
Output power: 75W
Working temperature: -40~+85 degrees
Operating frequency: 180KHz
Efficiency:96%（max)
Short circuit protection: yes(limit current 8A).
Over temperature protection
Input reverse polarity protection: None (if required, high current diode in series with the input).
L x W x H = 54 * 23 * 18mm
Application:
The DC/DC buck module applications the input voltage is higher than the output voltage of the buck field, such as battery, power transformer, DIY adjustable regulated power supply, 24V Vehicle notebook power supply,industrial equipment buck.12V buck to 3.3V, 12V buck to 5V, 24V buck to 5V,24V buck to 12V, 36V buck to 24V etc.
Package Included :
1 x XL4015 DC-DC Step Down Adjustable Power Supply Module LED Lithium Charger 5A Max
1x heat sink
Item 2
1. LED power indicator.
2. Button to switch measurement of the input or output voltage, and LED indicates the current measurement of the input or output voltage; The nixie tube can be turned off by another button. Mentioned states are able to be memorized, is not lost even if the power is disconnected. (On-board marked "IN" LED is turned on, the nixie tube display input voltage value, "OUT" LED bright display is the output voltage value).
3. Special launch, the voltmeter calibration function, will never exist voltmeter inaccurate!
Voltmeter calibration method:
(1) Output voltage calibration steps
Step 1, adjust the right button so that "OUT" LED lighted, the voltmeter shows the value of output voltage; Press the right button for more than 2 seconds, release, voltmeter and "OUT" LED flashes in synchronization so that you enter the output voltage calibration mode.
Step 2, press the right button (normal speed), the voltage value is adding up a unit; Press the left button, minus a unit; Due to a unit is less than 0.1V, the minimum voltage display to 0.1V, so you need to continuously press 1-5 times to see the voltmeter change 0.1V, how many times voltmeter change 0.1V by pressing the key, depending on the current display voltage, the higher the voltage, the fewer the number of press.
Step 3, press the right button for more than 2 seconds, release, to exit the output voltage calibration mode. All parameters set to automatically power down to save.
(2) Input voltage calibration steps
Step 1, adjust the right button so that "IN" LED lighted, the voltmeter shows the value of input voltage; press the right button for more than 2 seconds, release, voltmeter and "IN" LED flashes in synchronization so that you enter the input voltage calibration mode.
Steps 2 and 3, consistent with the output voltage calibration method.
Performance parameters:
1、Input voltage range：4～38VDC(Note:input voltage not exceeding 38V)
2、Output voltage range：1.25-36VDC adjustable
3、Output current: 0-5A
4、Output power: 75W
5、voltmeter range: 4 to 40V, error ±0.1V
6、Operating frequency: 180KHz
7、High efficiency up to 96%
8、Built in thermal shutdown function
9、Built in current limit function
10、Built in output short protection function
11、Input reverse polarity protection: None (if required, high current diode in series with the input).
12、L x W x H =6.6*3.9*1.8CM
Application:
The DC/DC buck module applications the input voltage is higher than the output voltage of the buck field, such as battery, power transformer, DIY adjustable regulated power supply, LCD Monitor and LCD TV，portable instrument power supply，telecom/networking equipment,24V vehicle notebook power supply,industrial equipment buck.12V buck to 3.3V, 12V buck to 5V, 24V buck to 5V,24V buck to 12V, 36V buck to 24V etc.
Package included：
1 x 5A Adjustable Power CC/CV Step Down Charge Module LED Driver Voltmeter
Item 3
Size: 51 * 26.3 * 14 (L * W * H) (mm)
Operating Temperature: -40 ℃ to +85 ℃
Voltage Regulation: ± 2.5%
Load Regulation: ± 0.5%
Output ripple: 50mV (max) 20M bandwidth
Switching frequency: 300KHz
Conversion efficiency: 95% (the highest)
Output current: adjustable maximum 5A
Output voltage: 0.8V-30V
Input voltage: 5V-32V
Rectification: non-synchronous rectification
Module Properties: non-isolated constant current and voltage module.
Advantage:
CC CV
Low ripple
When the module charges a battery, it first use constant current to protect the battery. check the curse above.
Package included:
1 x Lithium Charger Step down 5A 5V-32V to 0.8V-30V Power Supply Module LED Drive 5A
Item 4
1、Input voltage range:6～38VDC(Note:input voltage not exceeding 38V)
2、Output voltage range:1.25-36VDC adjustable
3、Output current: 0-5A
4、Output power: 75W
5、High efficiency up to 96%
6、Built in thermal shutdown function
7、Built in current limit function
8、Built in output short protection function
9、Input reverse polarity protection: None (if required, high current diode in series with the input).
10、L x W x H =61.7*26.2*15mm
11、Weight: 20g
Application
1、Use as a step-down modules with overcurrent protection capabilities
Usage:
(1) adjust the “voltage potentiometer” so that the output voltage reaches the value you want.
(2) use a multimeter to measure the output short-circuit current with 10A stalls, while regulating the “current potentiometer” so that the output current reaches a
predetermined overcurrent protection value. (For example, the meter displays the current value of 4A, then you
can use the module to a maximum current of 4A)
(3) Connected to the load.
2、Use as a battery charger
Usage:
(1). Make sure you need to charge the battery float voltage and charging current; (if lithium parameters 3.7V/2200mAh,
then the float voltage is 4.2V, the maximum charging current 1C, ie 2200mA)
(2). Under no-load conditions, adjust the “Voltage potentiometer” so that the output voltage reaches the float voltage;
(if to 3.7V rechargeable lithium battery, the output voltage can be adjusted to 4.2V)
(3). use a multimeter to measure the output short-circuit current with 10A stalls, while regulating the “current potentiometer” so that the output current reaches a
predetermined Charging current value.
(4). Charge turn lamp current factory default is 0.1 times the charging current; (Battery during charging current is
gradually reduced, if the charge current setting is 1A, then when the charge current is less than 0.1A, blue lights turned
off, the green light is on, which means that the battery is fully charged)
(5).connected to the battery charge.
(1,2,3,4 steps as: Output is unloaded, do not connect the battery)
3、Use as a LED constant current driver module
Usage:
(1). adjust the “voltage potentiometer” so that the output voltage reaches the value you want.
(2). use a multimeter to measure the output short-circuit current with 10A stalls, while regulating the “current potentiometer” so that the output current reaches a
predetermined LED operating current.
(3). Connect LED, work.
(1,2 steps as: Output is unloaded, do not connect LED)
Package included：
1 x 5A Lithium Charger CV CC buck Step down Power Supply Module LED Driver
Item 5
DC-DC adjustable step-down power Supply module ,5A Large current
Areas of application:
DIY mobile power supply, car power, communications equipment power supply, etc.
input voltage:5V-32V
output voltage:0.8V-24V
output current: peak 5A (more than 3.5A work need to strengthen The cooling)
Conversion efficiency:90%
size:43*21*14 mm(L*W*H)
The step-down module can easily reach 4 a, 50 w, add heat sink can reach 75 w, under the condition of extremely high price!
Modules window: 5 a high-power high efficiency low ripple Module performance and features:Module properties: the isolation step-down module (BUCK)4-38 v
input voltage: (please try not to exceed 38 v input)
Output voltage: 1.25-32 v continuous adjustable
Output current: 0-5 A, it is recommended to use in 4.5 A.
Output power: it is recommended that use within the 75 w, more than 50 w please add heat sink.
Working temperature: - 40 ~ + 85 degrees
Working frequency: 180 KHZ
Conversion efficiency: up to 96% (efficiency and the input, output voltage, current and pressure difference)
Load regulation: S (I) 0.8% or less
Voltage regulation: S (u) of 0.8% or less
Power light: yes
Short circuit protection: (limit current 8 a)
Over temperature protection: (over temperature after automatic shut off output)
Input reverse connect protection: no, (such as the need to please in the input string into the high current diode)
Installation method: 2 3 mm wire the self-contained
Connection mode: welding, V - IN for the input, V - OUT for the output
Package include:
1 x XL4015 Step Down Spannungsregler 5A einstellbar Modul für Arduino Power Supply
Payment Method
Returns Policy
Feedback
Payment Method
1. PayPal payment accepted only.
2. Items will be shipped to your eBay address. Please make sure it is correct.
Returns Policy
1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase.
2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer.
3. Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.
4. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response.
Feedback
When you satisfied with our product and services please leave us positive feedback.
If a problem occurs, contact us immediately with any email request. Just contact us using the " Ask the seller a question" link on eBay.
Am 05.01.21 hat der Verkäufer die folgenden Angaben hinzugefügt:
