-40%
WT588D USB Audio Burner Voice Programmer Downloader WT588D-16P VoiceChip Tester
€ 3.47
- Description
- Size Guide
Description
WT588D USB Audio Burner Voice Programmer Downloader WT588D-16P VoiceChip TesterDescription:
After compiling the engineering document into a BIN file on the computer WT588D VioceChip software, the WT588D module and the WT588D memory (which need to be used with the conversion seat) are placed on the locking seat, and the 16P and 28P modules in the WT588D module are only It needs to be placed at the bottom (the gap is facing the rocker of the locking seat), and then the engineering information is downloaded to the WT588D module or the related FLASH memory through the USB data line. When downloading, the USB terminal directly supplies power to the download board without plugging in the DC9V power supply. Edit the voice and control mode and trigger mode from the computer using WT588D VoiceChip software, and then download to download the project information to the WT588D module.
1, DAC audio output, requires an external power amplifier, and the WT588D module is set to DAC output mode;
2, PWM audio output, directly drive the speaker, WT588D module needs to be set to PWM output mode;
3. Online download output line interface;
4, reset button (when the connection is interrupted, or the connection process is wrong, and after the download is complete, you can click this button to reset);
5, test button, ten buttons K1, K2, K3, K4, K5, K6, K7, K8, K9, K10 correspond to I / O port P00, P01, P02, P03, P04, P05,
P06, P07, P10, P11;
6, I / O port lead line.
7, BUSY busy signal indicator
8, the power indicator
9, DC9V power input
10. The USB cable input slot (large) is connected to the computer via the USB cable. When connected, the power is supplied by USB.
11. Locking seat, can be placed WT588D module, WT588D external SPI-Flash (requires conversion seat), placed on the bottom.
12, ∮ 3.5mm audio seat, DAC audio output, there is a pin at the position above the audio block, the DAC output should be shorted, and the PWM output must be disconnected.
13. The I/O port leads the pin, and the upper row is the I/O port pin. From left to right, it is P00, P01, P02, P03, P04, P05, P06, P07, P10, P11, P12. The lower row is all ground. When the parallel port control mode is selected, the jumper cap can be used to short the I/O port to the ground to obtain the voice address.
Package Included:
1PCS WT588D USB Audio Burner Voice Programmer Downloader VoiceChip WT588D-16P
Refund
About Shipping
Payment
Refund
All package need to
wait 30 days
(US only need 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
About Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Payment
We accept PayPal only. But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Am 15.04.21 hat der Verkäufer die folgenden Angaben hinzugefügt:
