PICkit 3 PIC Simulator emluator Programmer Controller with USB Cable

Description

Sophisticated product, please handle with care; quality first, credit upmost;
Your satisfaction is our pursuit;The strength of technology decide the quality of technology.                                         if  you have any problem,pls contact with us.
PICkit3 PIC Simulator Emluator Programmer Controller With USB Cable
Features
:
Full-speed USB support using Windows standard drivers
Real-time execution
Processors run at maximum speeds
MPLAB IDE compatible (free copy included)
Built-in over-voltage/short circuit monitor
Firmware upgradeable from PC/web download
Totally enclosed
Supports low voltage to 5 volts (1.8v to 5.0v range)
Diagnostic LEDs (power, active, status)
Read/write program and data memory of microcontroller
Erase of all memory types (EEPROM, ID, configuration and program) with verification
Freeze-peripherals at breakpoint
Program up to 512K byte flash with the Programmer-to-Go
Basic Debugger System
The debugger system can be configured to use standard ICSP communication for both programming and debugging functions.
CAUTION
: Do not change hardware connections while the PICkit3 or target is powered.
Supported Devices
Refer to MPLAB IDE v8.76, the following devices are supported:
11 Series Serial EEPROM Devices
11LC/AA010,11LC/AA020,11LC/AA040,11LC/AA080,11LC/AA160
24 Series Serial EEPROM Devices
24LC/AA/C00,24LC/AA01B, 02B, 04B, 08B,24LC/AA16B, 32A,24LC/AA/FC64, 128, 256, 512,24LC/AA/FC1025
25 Series Serial EEPROM Devices
25LC/AA010A, 020A, 040A,25LC/AA080A, 080B, 160A, 160B,25LC/AA320A, 640A,25LC/AA128, 256, 512, 1024
93 Series Serial EEPROM Devices
25LC/AA/C46A, 46B, 46C,25LC/AA/C56A, 56B, 56C,25LC/AA/C66A, 66B, 66C,25LC/AA/C47A, 76B, 76C
,25LC/AA/C48A, 86B, 86C
MCP250xx CAN Devices
MCP25020, 25025,MCP25050, 25055
Debugger To Target Communication
Connecting the PICkit3 to the target board through standard ICSP interface using 6-pin connector. The programmer connector pinout is shown in the figure below:
PICkit3 Status LEDs
The Status LEDs indicate the status of the PICkit3.
Power (green) – Power is supplied to the PICkit3 via the USB port.
Active (blue) – The PICkit3 has connection to the PC USB port and the communication link is active.
Status:
Busy (yellow) – The PICkit3 is busy with a function in progress, such as programming.
Error (red) – The PICkit3 has encountered an error.
Package Included:
1PCS *
PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board S
Shipping
Feedback
Payment
Return policy
Contact us
Shipping
1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3.
All package need to
wait 30 days
,
Please take care it.Less than 30 days,we can't take a refund
.
Feedback
1.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help.
2.Please DON'T leave negative or neutral feedback if you haven't received item in 30 days, because we have mentioned the shipping time repeatedly.
Payment
1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.
3.Buyers
are responsible
for import duties,custom fees and taxes, if any, please check your country.
Return policy
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.
Contact us
1. If you have any questions, please feel free to email our service specialists.
2.Just contact us using the " Ask the seller a question" link on eBay.
3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.
PICkit3 PIC Simulator Emluator Programmer Controller With USB Cable
Features
:
Full-speed USB support using Windows standard drivers
Real-time execution
Processors run at maximum speeds
MPLAB IDE compatible (free copy included)
Built-in over-voltage/short circuit monitor
Firmware upgradeable from PC/web download
Totally enclosed
Supports low voltage to 5 volts (1.8v to 5.0v range)
Diagnostic LEDs (power, active, status)
Read/write program and data memory of microcontroller
Erase of all memory types (EEPROM, ID, configuration and program) with verification
Freeze-peripherals at breakpoint
Program up to 512K byte flash with the Programmer-to-Go
Basic Debugger System
The debugger system can be configured to use standard ICSP communication for both programming and debugging functions.
CAUTION
: Do not change hardware connections while the PICkit3 or target is powered.
Supported Devices
Refer to MPLAB IDE v8.76, the following devices are supported:
11 Series Serial EEPROM Devices
11LC/AA010,11LC/AA020,11LC/AA040,11LC/AA080,11LC/AA160
24 Series Serial EEPROM Devices
24LC/AA/C00,24LC/AA01B, 02B, 04B, 08B,24LC/AA16B, 32A,24LC/AA/FC64, 128, 256, 512,24LC/AA/FC1025
25 Series Serial EEPROM Devices
25LC/AA010A, 020A, 040A,25LC/AA080A, 080B, 160A, 160B,25LC/AA320A, 640A,25LC/AA128, 256, 512, 1024
93 Series Serial EEPROM Devices
25LC/AA/C46A, 46B, 46C,25LC/AA/C56A, 56B, 56C,25LC/AA/C66A, 66B, 66C,25LC/AA/C47A, 76B, 76C
,25LC/AA/C48A, 86B, 86C
MCP250xx CAN Devices
MCP25020, 25025,MCP25050, 25055
Debugger To Target Communication
Connecting the PICkit3 to the target board through standard ICSP interface using 6-pin connector. The programmer connector pinout is shown in the figure below:
PICkit3 Status LEDs
The Status LEDs indicate the status of the PICkit3.
Power (green) – Power is supplied to the PICkit3 via the USB port.
Active (blue) – The PICkit3 has connection to the PC USB port and the communication link is active.
Status:
Busy (yellow) – The PICkit3 is busy with a function in progress, such as programming.
Error (red) – The PICkit3 has encountered an error.
Package Included:
1PCS *
PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board S
Shipping
Feedback
Payment
Return policy
Contact us
Shipping
1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3.
All package need to
wait 30 days
,
Please take care it.Less than 30 days,we can't take a refund
.
Feedback
1.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help.
2.Please DON'T leave negative or neutral feedback if you haven't received item in 30 days, because we have mentioned the shipping time repeatedly.
Payment
1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.
3.Buyers
are responsible
for import duties,custom fees and taxes, if any, please check your country.
Return policy
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.
Contact us
1. If you have any questions, please feel free to email our service specialists.
2.Just contact us using the " Ask the seller a question" link on eBay.
3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.
Am 11.12.21 hat der Verkäufer die folgenden Angaben hinzugefügt: