-40%
ESP32-CAM OV2640 2MP Camera Module - USB Type-C M5STACK M5CAM - AI developement
€ 4.67
- Description
- Size Guide
Description
ESP32-CAM with OV2640Description:
1. ESP32-CAM is a WIFI+ bluetooth dual-mode development board that uses PCB on-board antennas and cores based on ESP32 chips. It can work independently as a minimum system.
2. ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc.
3. Fully compliant with WiFi 802.11b/g/n/e/i and bluetooth 4.2 standards, it can be used as a master mode to build an independent network controller, or as a slave to other host MCUs to add networking capabilities to existing devices.
4. ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an ideal solution for IoT applications.
Features:
- Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
- Low-power dual-core 32-bit CPU for application processors
- Up to 240MHz, up to 600 DMIPS
- Built-in 520 KB SRAM, external 4M PSRAM
- Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
- Support OV2640 and OV7670 cameras with built-in flash
- Support for images WiFI upload
-Support TF card
- Support multiple sleep modes
- Embedded Lwip and FreeRTOS
- Support STA/AP/STA+AP working mode
- Support Smart Config/AirKiss One-click distribution network
- Support for serial local upgrade and remote firmware upgrade (FOTA)
- Support secondary development
- Branding at the board may vary between Espressif and AI-thinker
Note:
This product contains the OV2640 Camera Module.
Package Included:
1 x ESP32-CAM Module
1 x Camera Module OV2640 2MP
Product Specifications:
Module model
ESP32-CAM
Package
DIP-16
Size
27*40.5*4.5(±0.2)mm
SPI Flash
default 32Mbit
RAM
internal520KB+external 4M PSRAM
bluetooth
bluetooth4.2BR/EDR and BLE standards
Wi-Fi
802.11 b/g/n/e/i
Support interface
UART, SPI, I2C, PWM
Support TF card
Maximum support 4G
IO port
9
Serial port rate
default 115200 bps
Image output format
JPEG (only supported by OV2640), BMP, GRAYSCALE
Spectrum range
2412 ~ 2484MHz
Antenna form
onboard PCB antenna , gain 2dBi
Transmit power
802.11b: 17±2 dBm (@11Mbps)
802.11g: 14±2 dBm (@54Mbps)
802.11n: 13±2 dBm (@MCS7)
Receiving sensitivity
CCK, 1 Mbps : -90dBm
CCK, 11 Mbps: -85dBm
6 Mbps (1/2 BPSK): -88dBm
54 Mbps (3/4 64-QAM): -70dBm
MCS7 (65 Mbps, 72.2 Mbps): -67dBm
Power consumption
Turn off the flash: 180mA@5V
Turn on the flash and adjust the brightness to the maximum: 310mA@5V
Deep-sleep: The lowest power consumption can reach 6mA@5V
Moderm-sleep: up to 20mA@5V
Light-sleep: up to 6.7mA@5V
Security
WPA/WPA2/WPA2-Enterprise/WPS
Power supply range
5V
Operating temperature
-20 °C ~ 85 °C
Storage environment
-40 °C ~ 90 °C, < 90%RH
ESP32-CAM Picture Output Format Rate:
QQVGA
QVGA
VGA
SVGA
JPEG
6
7
7
8
BMP
9
9
-
-
GRAYSCALE
9
8
-
-
Test environment: camera model: OV2640 XCLK: 20MHz, the module transmits pictures to the computer browser by WiFi.
M5CAM - ESP32-CAM with USB type-C by M5STACK®
ESP32CAM
is a development board for image recognition. It features an ESP32(4M Flash + 520K RAM) chip and 2-Megapixel camera(OV2640). It also supports image transmission via Wi-Fi and debuging through USB Type-C port.
The hardware comes preloaded software, programmed by ESP-IDF. It is an application to run Wi-Fi camera. The output image is size 600*800, since it's 2-Maga camera, you sure can optimize the software to output the maximum size of photos.
To see what this software can do?
Please flow the steps.
1.
Power the board via USB type-C or GROVE
2.
Use your phone to Wi-Fi scan an AP name start with 'm5stack-' and click to connect this AP.
Open up web browser on your phone and visit 192.168.4.1
Then here comes the picture. Video is about 5-6 frames per senconds. not super fast.
The hardware also comes with some reserved weld pad, just in case you want put these chips back on board.
USB type-C or GROVE power input
6-axis gyroscope (MPU6050)
pressure sensor (BMP280)
analog MIC (SPQ2410)
Battery socket
Product Features
ESP32 specifications
Dual-core Tensilica LX6 microprocessor
Up to 240MHz clock frequency
520KB internal RAM
4MB Flash memory
Integrated 802.11 BGN WiFi transceiver
Integrated dual-mode Bluetooth (classic and BLE)
Hardware accelerated encryption (AES, SHA2, ECC, RSA-4096)
CP2104 USB TTL
OV2640 sensor
Output Formats(8-bit):
YUV(422/420)/YCbCr422
RGB565/555
8-bit compressed data
8-/10-bit Raw RGB data
Maximum Image Transfer Rate
UXGA/SXGA: 15fps
SVGA: 30fps
CIF: 60fps
Scan Mode: Progressive
Camera specifications
Field of View :
65 degree
Maxmium Pixel: 2M
Size: 20.5 × 46.5 × 11.5m
Kit includes
M5 ESP32CAM (M5CAM)
Camera Module OV2640 2MP
camera case
cooling element
