Digital LCD Temperature Humidity Controller Thermostat Sensor Timing Auto ON/OFF

Description

Digital LCD Temperature Humidity Controller Thermostat Sensor Timing Auto ON/OFF
Note:
The product is shipped without a battery. Need to buy the battery by yourself.
The battery model: CR1220 3V button. The battery needs to be calibrated for the first time.
Time calibration operation mode:
In the case of power on, long press the setting key to enter the setting interface, and the up and down keys can select any menu of P1-H2. If you need to calibrate the time, use the up and down keys to select the P5 menu, short press the set key to confirm and enter, and then adjust the time through the up and down keys.
Product parameter：
Product name:
Intelligent temperature controller
Product model:
W-1213
Power supply voltage: AC110-220V
Working frequency: 50HZ
Temperature range: -40~+120°C
Temperature measurement accuracy: ±0.5°C
Sensor cable length: 100CM
Size: 79.5*43*35mm
Shell material: surface shell ABS, bottom shell flame retardant ABS
Display panel description
Heat (corresponding icon display): heating mode, in heating mode, heating
The relay works.
Cool (corresponding icon display): Cooling mode, in cooling mode, cooling
The relay works.
Timer: Timer switch, in timer mode, the icon flashes
OBJ LOW: Set lower limit of target temperature
OBJ HIGH: target temperature setting upper limit
Horizontal marquee: increasing. Going up means heating decreasing and going down means cooling
Key Description
1. Power button
①In the power-on state, long press to power off
②In the shutdown state, long press to turn on
③In the setting mode, short press to confirm and press again to return to the home page display
temperature.
2. Set key
①Long press to enter the setting mode option
②In the setting mode option, short press to confirm the currently selected setting mode.
3. Minus key
In the setting mode interface, short press-times to subtract 1, long press to continue to subtract
In the non-setting interface, long press to cancel the timing time.
4. Add key
In the setting mode interface, short press--times to increase by 1, long press to continue to increase.
In the non-setting interface, short press to view the timer shutdown time setting value, long press
timing.
5. Combination keys
Setting key + number minus (restore factory settings)
In the power-on state, pressing the key combination at the same time will restore the factory settings (long press)
Mode description
Under normal operation, the LCD screen displays the real-time measured value of the current temperature, and
Automatic recognition and conversion of cooling and heating working modes.
1. Cooling mode:
①When the real-time temperature ≥ the target temperature upper limit setting value, enter the cooling mode Type, the Cool indicator icon is on, the marquee decreases, and the refrigeration relay works.
②When the refrigeration temperature drops to the lower limit set value of the target temperature, the refrigeration relay
The thermostat stops working, and the thermostat enters the temperature control state, and the temperature control range is the target temperature
Upper and lower limit setting value.
③When the refrigeration temperature rise value ≥ the target temperature upper limit setting value, the snowflake mark
The logo starts to flash, the thermostat enters the press delay state, and the press delay time is over.
The cold relay only starts to work, (press delay time can be set)
2. Heating mode:
①When the real-time temperature ≤ the lower limit set value of the target temperature enters the heating state,
The Heat indicator icon lights up, the marquee increases, and the heating relay works.
②When the heating temperature reaches the target temperature upper limit setting value, the heating relay stops
Stop working, the marquee stops, the thermostat enters the temperature control state, the temperature control range is the target
Standard temperature upper and lower limits.
3. Timing on/off mode:
①Set the scheduled shutdown time in the power-on state through the number plus key.
In the timer mode, you can turn off the timer shutdown function by long pressing the plus button
②Through the number minus key, set the timing power-on time in the off state,
In the timer mode, you can turn off the timer boot function by long pressing the minus button.
Tips
①In normal mode, short press the power button or plus button to view the setting parameters, 1 second
Back to normal mode later.
②In the setting mode, if no button is pressed, it will automatically return after 10 seconds
Normal working mode.
③In the setting mode, when a certain option value is set, if the setting is not pressed
Press the key or power key to confirm and return, and automatically return to normal working mode after 10 seconds
When, the value will not be saved
Package Included:
1PCS*Temperature Controller
Time calibration operation mode:
In the case of power on, long press the setting button to enter the setting interface, short press the setting button to quickly switch (P/F/H), set the time to H, select H1-H5 by the up and down keys, and select the corresponding if you need real-time clock setting H1 item, short press the power button to enter the setting time, the up button is to increase, the down button is to decrease, and the power button is to confirm
Instructions for setting operation:
1. In the case of power on, long press the setting button to enter the setting interface, short press in the setting interface to switch quickly (P/F/H), you can use the up and down keys to select P1-P5/F1-F4/H1-H5, and then Short press the power button to confirm and enter the setting parameters
Product parameters:
Product name:
Intelligent temperature and humidity controller
Product model:
W-1212
Power supply voltage: AC110-220V
Working frequency: 50HZ
Measuring range: -40~+120°C 0~100%RH
Measurement accuracy: temperature ± 0.3°C humidity ± 3%RH
Sensor cable length: 100CM
Size: 79.5*43*36mm
Shell material: surface shell ABS, bottom shell flame retardant ABS
Tips:
①In normal mode, short press the setting key or plus and minus keys to view the setting parameters,
Return to normal mode after 1 second.
②In the setting mode, if no button is pressed, it will automatically return after 10 seconds
Normal working mode.
③In the setting mode, when a certain option value is set, if the power is not pressed
The source key confirms and returns, it will automatically return to the normal working mode after 10 seconds, and the value will not save.
Key Description:
1. Power button: ①Long press the switch
②In the setting mode, short press is the confirmation key
2. Setting key: ①Short press to view the temperature control mode, short press again to view the humidity control mode
②Long press to enter the setting interface, and short press the setting key to select
Select temperature control and humidity control or time mode (ie P, F and H mode switch)
3. Add key: ①On the homepage, short press to view the target temperature switch time, long press to turn on
Target temperature switching time
②In the menu mode, short press and 1 long press and continue to add
4. Minus key: ①Short press on the homepage to view the target humidity switch time, long press to turn on
Target humidity switch time
②In the menu mode, short press to decrease 1 and long press to continue to decrease
5. Combination key: setting key + number minus (restore factory settings)
In the power-on state, pressing and holding the key combination at the same time will restore the factory settings
Mode description:
Manual heating and cooling in temperature control mode and humidification and dehumidification in humidity control mode
Go to set
1. Temperature control mode:
1. Refrigeration mode: (You can short press the setting button on the home page to view, or you can see on the screen
Snowflakes sign, that is, the current cooling mode)
①When real-time temperature ≥ target temperature setting value (OBJ TEMP) + temperature difference setting
It enters the refrigeration state when the value is reached, the relay works and starts refrigeration.
②When the real-time temperature drops to the target temperature setting value (OBJTEMP), the cooling
The relay stops working, the thermostat enters the temperature control state, and the temperature control range is the temperature difference setting
value.
③When real-time temperature ≥ target temperature setting value (OBJ TEMP) + temperature difference again
When the set value is set, the thermostat enters the compressor delay state, and the refrigeration relay after the compressor delay expires
The device just started working.
2. Heating mode: (You can short press the setting button on the home page to view, or you can see on the screen.
Sun sign, that is, the current heating mode)
① When the real-time temperature ≤ target temperature setting value-temperature difference setting value, enter heating
State, the heating relay works.
②When the heating temperature reaches the target temperature value, the heating relay stops working,
The thermostat enters the temperature control state, and the temperature control range is the temperature difference setting value.
Two, humidity control mode:
1. Dehumidification mode: (You can short press the setting button on the home page to view, or you can see on the screen
No water drop sign, that is, the current dehumidification mode)
①When the real-time humidity and humidity temperature difference value (OBJ HUM) ≥ the target humidity value, continue
The appliance starts to work and begins to dehumidify
②When the dehumidification humidity reaches the target humidity value, the dehumidification relay stops working,
Enter the humidity control state, the humidity control range is the humidity setting value.
2. Humidification mode: (You can short press the setting button on the home page to view, or you can see on the screen
Water drop mark, that is, the current humidification mode)
①When real-time humidity + humidity temperature difference value (OBJ HUM) ≤ target humidity value, continue
The appliance starts to work and humidifies
②When the humidification humidity reaches the target humidity value, the humidification relay stops working,
Enter the humidity control state, the humidity control range is the humidity setting value.
Timing description:
Temperature timing switch operation instructions:
①Add the key to control the temperature timing, short press to view the timing on or off the target temperature
, Long press the plus key to start timing
②In the home page interface, short press the plus key to display one one: one TEMP (for
Temperature timer shutdown) Long press the plus button to turn off the target temperature, and it will display when the long press starts
XX:XX TEMP
③In the home page interface, short press the plus key to display
(For warm
(Turn on at a fixed time) long press the plus key to turn on the target temperature regularly, and it will display when the long press starts
XX:XX time
Humidity timer switch operation instructions:
①The minus key controls the humidity timing, short press to view the timing on or off the target humidity
, Long press the minus button to turn on the timing
②In the home page interface, short press the minus button to display one one: one HUM (when
(Previously is humidity timing shutdown) Immediately long press the plus button to turn on the timing shutdown target temperature, when the
Display XX:XX HUM after pressing start
③In the home page interface, short press the minus button to display --:-- (currently
When the temperature is turned on, long press the plus button to turn on the target temperature at the time, when the long press starts
Display XX:XX time after
Package Included:
1PCS*Intelligent temperature and humidity controller
Note: The product is shipped without a battery. Need to buy the battery by himself. The battery model: CR1220 3V button. The battery needs to be calibrated for the first time.
Payment Method
Returns Policy
Feedback
Payment Method
1. PayPal payment accepted only.
2. Items will be shipped to your eBay address. Please make sure it is correct.
Returns Policy
1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase.
2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer.
3. Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.
4. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response.
Feedback
When you satisfied with our product and services please leave us positive feedback.
If a problem occurs, contact us immediately with any email request. Just contact us using the " Ask the seller a question" link on eBay.
Am 10.09.21 hat der Verkäufer die folgenden Angaben hinzugefügt: