-40%
4 Achsen USB Mach3 CNC Kontrolleur Kit Nema23 Schrittmotor 270oz +Treiber TB6600
€ 100.32
- Description
- Size Guide
Description
【Germany Stock & Free VAT & Free Duty】4 Achsen USB Mach3 CNC Kontrolleur Kit Nema23 Schrittmotor 270oz +Treiber TB6600
for CNC Router Engraving Milling Machine
New items have arrived our Germany Warehouse,welcome you to purchase.
We will send the item from Germany by DHL to EU Countries.
we will ship you order via
DHL
within 1 working day,fast shipping to you.
Package include:
4× Nema23 stepper motor
4× Tb6600 stepper motor driver
1× 4 Axis Mach3 USB CNC control board
1× USB Cable
1× CD disc
1× 350W 24V DC Switching power supply
100% Brand New and High Quality!!!
Nema23 Stepper motor 76mm/270Oz-in/ 3A 1.8Nm
General Specification:
Step angle accuracy: ±5%(full step,not load)
Resistance accuracy: ±10%
Inductance accuracy: ±20%
Temperature rise: 80deg Max(rated current,2 phase on)
Ambient temperature ----------—20deg ~+50deg
Insulation resistance:100MΩ Min,500VDC
Insultion Strength--------500VAC for one minute
Wiring:
A+ : Red
A- : Green
B+ : Yellow
B- : Blue
TB6600 stepper motor driver 4.5A
Parameters:
The working voltage is DC 10V-45V. It is recommended to use switching power supply DC32V for power supply.
Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.
Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.
The rated maximum output reaches: ±4.5A.
Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.
Automatic half-flow function.
Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.
Description:
The working voltage is DC 10-45V; it is recommended to use DV32V switching power supply.
There are two input terminals, both of which adopt the common anode input mode.
The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.
The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.
The motor rotates forward when CW is high or suspended, and reverses when it is low.
When EN is high or floating, it is working state, when it is low, it is offline.
Note:
The power supply cannot be connected reversely, otherwise the chip will be burnt out.
The set current should not exceed the rated current of the motor.
Mach3 USB motion control board 4 axis
Notice:
The motion control card for machine control, with strong professional.Requires the operator to have the relevant expertise!
Please strictly follow the instructions and warnings before using this product
If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power.
It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.
Feature:
This USB motion card does not need install any USB driver, Windows2000/XP/Windows7,can directly identify.
4-axis linkage, Maximum step-pulse frequency: 100KHz, support connect four stepper motor drives or servo drives.
Signal Output:0-10V, it can control the spindle motor speed through using mach3 software.
4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop.
4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps or other device.
Support for connecting electronic handwheel
(Note: the output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface.)
350W 24V DC switching power supply
Specification:
DC output: 24V 0-14.5A
Inlet stability: ±0.5%
Load stability: ±0.5%
DC voltage of Adjustable range: ±10%
AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switch
Overload protection: 105%-135% cut off the output, automatic recovery
Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover
Setup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full load
Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute
Isolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ
Working Temperature: -10℃～+50℃
Shipping
Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately
Items will be shipped within 1-2 days upon the receipt of payment.
Payment
We accept paypal payment, all Paypal must be confirmed(shipping and billing address must match and correct and it need tell us your telephone no for delivery)
Problem&Feedback
Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it.
We are a new member in ebay now, and need understand both of sides
Pls email us before you want to leave any negative feedback
Refund
When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos
Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Contact us
Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again
Customer’s satisfaction is very important to us.
